What are the advantages of titanium screws? In the process of alkali cleaning of titanium alloy rods, the lye is continuously taken away or evaporated by the workpiece. Therefore, it is necessary to replenish the lye and adjust it in time to keep the alkali composition relatively stable. Titanium screws, in the alkaline washing, insoluble slag deposits at the bottom of the tank, affecting the good thermal conductivity of the tank, and due to the gap caused by the precipitation, the steel tank is prone to electrochemical corrosion, greatly shortening its service life. Titanium screws should be cleaned up in time for sediment. It is a common practice to collect slag with a moving trough. When you need to eliminate deposits, simply hang the bottom of the active trough.

The yield strength is the yield limit when the metal material yields, that is, the stress that resists the slight plastic deformation. What are the advantages of titanium screws? For metal materials that have no obvious yielding phenomenon, the stress value that produces 0.2 residual deformation is defined as the yield limit, which is called the conditional yield limit or yield strength.

An external force greater than the yield strength will cause the part to fail and cannot be recovered. What are the advantages of titanium screws? For example, the yield limit of low carbon steel is 207 MPa. When the external force is greater than this limit, the parts will be deformed. If it is smaller than this, the parts will return to their original appearance.

(1) For materials with obvious yielding, the yield strength is the stress at the yield point (yield value);

(2) For materials in which the yielding phenomenon is not significant, the stress at the limit deviation from the linear relationship of stress-strain reaches a prescribed value (usually the original gauge length of 0.2). What are the advantages of titanium screws, which are usually used as an evaluation index for the mechanical properties of solid materials, and are the practical limits of use of materials. Because the necking occurs after the stress exceeds the yield limit of the material, the strain increases and the material is destroyed and cannot be used normally.

What are the advantages of titanium screws? Titanium rod manufacturers tend to cause plugging of filter parts when the flow rate of titanium rod filter is too large. To avoid this situation, you must know more about the use of titanium rod filters. For titanium screws, when using titanium rod filters, they should be operated according to the rated pressure specifications. Do not rush to adjust the pressure to ensure the flow rate is stable. Titanium screws, after skilled operation, also need to master the cleaning method of titanium rod filter. It needs to control the time when cleaning. It should not be too long or too short. According to the requirements of titanium rod filter, prepare disinfection solution for repeated cleaning. .

Titanium screws, when we use screws in our lives, there are really a lot of things, but the understanding of titanium alloy screws is the last word, or else the selection of inferior goods will be counterproductive. Therefore, when purchasing, you should find a business with a large titanium alloy screw. Like screws that are subject to high strength parts, then I would recommend not using aluminum, easy to wire, and solid titanium screws. What are the advantages of titanium screws? Titanium alloy screws are not only harder than stainless steel, but the finished products are also much lighter in weight than ordinary stainless steel screws. In addition, the titanium alloy screws and nuts have hard threads, and the wear resistance may be higher than that of ordinary stainless steel. Titanium screws, in addition to not easy to slip, the titanium alloy screws themselves have high material stability and good oxidation resistance. . Some titanium alloy screws have a large difference in hardness, so titanium alloy screws must be made of good materials, and titanium alloy screws have steel hardness.

What are the advantages of titanium screws? At present, the production of titanium and titanium alloy wire at home and abroad mainly adopts the processes of drawing, grinding, annealing, acid-base washing, cut-off, straightening, etc., which requires twenty in the whole production process. Pulling times, three to four intermediate grinding, ten intermediate annealing, two to three acid-base washing processes, straightening process, etc. Titanium screw, in the case of high temperature heating, the diameter of the wire is controlled by the hole mold. The straight wire processing is difficult, the surface precision is poor, the hydrogen absorption and oxygen are serious, and the single plate weight is low, which can not meet the requirements of high precision titanium; the acid and alkali cleaning surface has Very polluting, titanium screws can only pickle the surface of titanium, and can not produce bright titanium. The straightening process will cause the surface of the titanium material to form a straightening pattern which is difficult to eliminate, and the surface damage of the titanium material is more serious.

Previous: Titanium Alloy Elimination Process And Annealing Process

Next: Physicochemical Properties Of Titanium And The Influence Of The Elements Contained In The Welding